Recent searches

No recent searches

Search options

Only available when logged in.
101010.pl is one of the many independent Mastodon servers you can use to participate in the fediverse.
101010.pl czyli najstarszy polski serwer Mastodon. Posiadamy wpisy do 2048 znaków.

Administered by:

Server stats:

474
active users

101010.pl: AboutStatusProfiles directoryPrivacy policy

Mastodon: AboutGet the appKeyboard shortcutsView source codev4.5.0-alpha.2

#Vcore

0 posts0 participants0 posts today
8petrosNie wiem, czy opary <a href="https://petroskowo.pl/search?tag=PLA" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>PLA</span></a> są szkodliwe, ale na pewno uzależniają. Po wielu miesiącach znów się drukuje. Oboje się cieszymy i wpatrujemy jak w skrzyżowanie telewizora z kominkiem. <a href="https://petroskowo.pl/search?tag=RatRig" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>RatRig</span></a> <a href="https://petroskowo.pl/search?tag=V-Core" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>V-Core</span></a> 400^3
8petrosI got stuck, troubleshooting my <a href="https://petroskowo.pl/search?tag=BTT" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>BTT</span></a> <a href="https://petroskowo.pl/search?tag=BigTreeTech" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>BigTreeTech</span></a> <a href="https://petroskowo.pl/search?tag=Octopus" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>Octopus</span></a> 1.1 mainboard, installed in newly assembled <a href="https://petroskowo.pl/search?tag=RatRig" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>RatRig</span></a> <a href="https://petroskowo.pl/search?tag=V-core" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>V-core</span></a> <a href="https://petroskowo.pl/search?tag=3Dprinter" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>3Dprinter</span></a>, running <a href="https://petroskowo.pl/search?tag=RatOS" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>RatOS</span></a> aka <a href="https://petroskowo.pl/search?tag=Klipper" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>Klipper</span></a>.<br><br>Both <a href="https://petroskowo.pl/search?tag=nozzle" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>nozzle</span></a> (<a href="https://petroskowo.pl/search?tag=extruder)" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>extruder)</span></a> <a href="https://petroskowo.pl/search?tag=heater" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>heater</span></a> and <a href="https://petroskowo.pl/search?tag=hotbed" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>hotbed</span></a> one do not warm up. Beyond all doubt (using external power sources and hairdryer) I confirmed that both thermistors, heaters and wiring are ok. <br><br><strong>Under warranty, RatRig sent me replacement board, which I configured, flashed with updated firmware and got the same error. </strong><br>I also tried to redirect the nozzle heater power to another pin (see in the config file at <a href="https://lib.tepewu.pl/f/8f1d29fe05d44c77a329/" rel="nofollow noopener" target="_blank">lib.tepewu.pl/f/8f1d29fe05d44c…</a>) where I hooked up the multimeter. Nothing happened, when I set up nozzle temp to 50*C - after timeout I had the same error "extruder is not heating fast enough", thus klipper shutdown.<br><br>I cannot believe to have such a bad luck to got two boards with the same hardware fault (especially that steppers and hotbed probe work perfectly), so it is something I do not know - and I run out of ideas. <br><br>Please, somebody suggest something new. Hjalp.
COMFY Tech Artel<a href="https://petroskowo.pl/search?tag=RatRig" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>RatRig</span></a> <a href="https://petroskowo.pl/search?tag=V-core" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>V-core</span></a> 3.1 nabiera kształtów. Już się szykuję na ból i ekstazę kalibrowania i tuningu...<br><br><a href="https://petroskowo.pl/search?tag=Druk3D" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>Druk3D</span></a> <a href="https://petroskowo.pl/search?tag=CoreXY" class="mention hashtag" rel="nofollow noopener" target="_blank">#<span>CoreXY</span></a>
TrendingLive feeds
About